People are increasingly thinking about ecology, so conscious sellers and buyers prefer paper packages that do not cause such harm nature as polyethylene. In some stores, you will be offered ordinary browning paper bags, others use packages as advertising space. And, I must say, some paper bags look very interesting, and you don't want to throw them into the garbage bucket at all. In this article we will tell, as an unusual lamp from the usual paper package.

Especially simple this project will seem to those who have basic skills in Origami technique. Although the scheme is quite simple, so the newcomer can also mask it.

Tip: If you do not have extra packages, you can work on a sheet of regular paper.

In Origami, there are the simplest bends - "Mountains" and "Valley". "Gorka" is when the edge of the bend is aimed at you, and the "valley" is the opposite.

Important: When choosing a light bulb for a lamp with a paper lamp, you need to pay special attention to the amount of heat released. LED light bulbs will be best, which, when energy consumption, 7.5 W shine at the level of 40-watt light bulbs. In no case use incandescent lamps.

Materials and tools:

• 2 paper packages
• scissors
• glue or double-sided adhesive
• needle or awl
• thread
• adhesive Pistol
• twine
• cable, plug and electric cartridge
• branched branch

How to make a paper lamp do it yourself

Take two of you like paper packages, cut the handles and bottom. Cut the package at the place of the gluing, as a result of each package you should get a sufficiently long cloth, the dimensions of which depend on the value of the used package.

Take one cloth, fold it twice, then every half is still twice. Continue until you divide the cloth on 16 equal parts. Fold the cloth over the fan fan lines.

Now each resulting scallop is needed to be folded on the diagonal. At this stage, it is not necessary to think about the "mountains" and "valleys", you just need to schedule the folding lines. So that the bends ended on the same level, on each of the ribs, you can put an imperceptible mark with a simple pencil.

In the same way, make the bends on the other hand. Now the ribs should be folded in the opposite direction.

The photo shows how the workpiece should look like after all manipulations.

From the second package in our case it took only half. Do with this workpiece the same manipulations with the only difference that at the first stage you need to bend, dividing into 8 equal parts.

Connect two paper glue blanks or bilateral scotch.

In the upper corners, pinched holes, stretch in them thread or ribbon.

Throw the corners so that you have a dome, like what you see in the photo.

Tie a thread on a bow, so later you can easily stretch the cable.

For such a lamp, a regular boring cable is hardly suitable. You can decorate it by wrapped with a thin beep and fixing its ends with hot glue.

It remains only to stretch the cable with a cartridge inside the lampshar. You can hang the lamp on a dry branch of a bizarre form, so it will look even more interesting.

Original articles in English.

Make something with your own hands and then decorate your home - what is not a subject of special pride? Homemade things allow you to reveal the creative potential in themselves and at the same time will significantly save. And the independent manufacture of lamps is no exception. Today you can find various ways to make the lighting device with your own hands. To do this, it is enough to drive into the search string "Luminaire of paper how to make with your own hands." But you no longer need it, because in this article we will try to give the most complete answer to this question. Here we will touch the fuel material for the lamp - paper.

Our article will also help you understand whether you will cope with such work, and whether the paper lamp is suitable for your interior.

Paper - What could be easier?

Light from paper lamp

Ease and airiness - this is what is associated with many paper. Therefore, the paper lamp will also drive these properties, bringing with you to various interiors:

• unusual;
• softening and smoothing the angularity;
• creating multiple and muted light, giving the atmosphere of romanticity and mystery.

Today, paper lighting devices are associated with Asia and East. It is here that not only paper, but also products from it appeared: umbrellas, lanterns, etc. East, as they say, the case is thin. This statement is perfectly embodied with paper and creativity, which is reborn into unique and unique lamps.
Despite the fact that China's homeland is considered China, paper lighting devices can be safely made in different style:

• japanese;
• chinese;
• pop art;
• eclectics;
• country;
• vintage, etc.

Note! Only manufacturing the lamp with their own hands, you can perfectly compare it with the rest of the interior, emphasizing or connecting together all the directions of the design used.

Since it is easy to work with paper, and it is possible to find it in the house in almost unlimited volumes, then today there are most diverse options for the assembly of paper luminaires. Consider the simplest and most popular of them.

Since the paper was first made in China, it is logical to start with the creation of the lighting instrument in Chinese style.

Chinese style lamp

Many prefer to make paper lamps precisely in the Chinese style, as in this case it turns out to be brought to the interior brightness, live paints and feeling of the holiday. All this, forces, achieve with the Chinese lamp.
From the materials you need:

• paper. It can be rice or ordinary. It is desirable that the sheets of paper are translucent, color or white;

Note! For the most similar similarity with the original Chinese folk lamps, you should work with rice paper.

• cartridge. It can be bought on the market or remove from the old chandelier;
• light bulb. Since the lamp will be made of paper, not heated light bulbs should be chosen as a source of light. It is best to stop your choice on LED bulbs.

In addition to the materials themselves, you will need some tools:

Scheme of chinese lantern

• pencil and ruler;
• stationery knife;
• awl;
• a thread.

The lamp assembly will occur as follows:

• we make markup on the back of the paper. So it turn out to create a relief. To make a Chinese flashlight, a scheme is needed, on which markings are made;
• bend paper on markups so that in the right places get a harmonic. Do not hurry in this matter, since the accuracy of execution will depend on how smooth and beautiful will be a flashlight;
• we collect the cartridge and the light bulb together;
• we make a selection of holes at the bottom and produce thread through it;
• wrap around the cartridge our paper lampshade. The edges of the paper sheet can be glued or simply impose on each other. The last option will help you quickly change the bulbs, without damaging the lampshade.

Ready lanterns

The complexity here may occur only in the right folding of the base of the lampshar. As a result, you will have a handsome and almost authentic Chinese flashlight. To give him a more beautiful appearance, you can write a lampshade paint, applying Chinese hieroglyphs or stylized drawings on it.

Frame lamp

In Japan, paper products are also very popular and widespread. Therefore, you can safely use Japanese motifs and when creating a paper luminaire. Paper (preferably rice) here is also the main element. But now it will be supplemented with bamboo chopsticks. Note! Bamboo grows in Japan, so this element will look great in the overall exposure of the lamp.
Here it will take the following list of materials:

• paper tracing (for lack of rice sheets);
• ceramic cartridge with a small base;
• thread, preferably fat;
• morida;
• a piece of MDF. Can be replaced by plywood;
• wire with switch and fork.

From the tools you need to have at hand:

• pVA glue;
• sandpaper;

Ready Japanese Paper Lamp

• scissors;
• pink;
• corolnic;
• brush.

For the base, we take plastic corners, bamboo / wooden slats or wire. We collect the basis of the lamp according to the following scheme:

• reiki cleaner with emery paper and cut under the height you need. It will be the height of the entire lamp;
• on the rails make marking in places of gluing. They will help to make a smooth and beautiful frame;
• shakes with glue and collect rails into a single design. For strength, the angular connections should be kept thick thread. This will help to strengthen the foundation, and also give it a decorative appearance. The frame itself can be round or square;
• a sheet of MDF will be used as a lid. In the sheet we do a hole for the cartridge;
• after that, all wooden structural elements are covered with a verse. On top of it you can put lacquer. Such protection will make a tree resistant to the negative impact of moisture and keeps it from wood insects;
• now it remains on the frame to attach paper sheets. They can be left clean, but it is better to pre-apply a Japanese pattern or hieroglyph. Sheets just glit to the frame.

This is a somewhat more complex in terms of the implementation of the lamp. But it turns out to be more durable and qualitative, which will be positively affected by the service life of the lighting device.

Glass and paper

The simplest in the manufacture of your own hands will be a glass lamp. This is a desktop portable lamp that is done very quickly and easily. For the manufacture of such a lighting device you will need:

• a thin sheet of paper (a specific pattern can be printed);
• round and high glasses;
• wire with a thickness of 1-2 mm;
• candle pills.

From the tools will be needed:

• scissors;
• pVA glue;
• pliers;
• stationery knife;
• scotch.

The algorithm of action here is the following:

Curved wire

• bend wire with pliers so that it acquires the view shown in the photo. At its lower part there will be a candle-tablet. The wire length ultimate should be a little more than the height of the glass. So it will be much more convenient to extract a candle from the tank;

• the glass itself is worth a decorated sheet of paper on which the pattern liked it is applied. Sheet gently glue to the glass. The tap of the tank can be reeded with a gypsum or polymer clay.

Finished glass

As you can see, we need a minimum of time and time, and as a result you will get a beautiful lamp, perfectly suitable for a romantic dinner or just a quiet, peaceful relaxation evening.

Paper tubes

Probably, the most original and unusual lighting device in our "paper" history will be a lamp of paper tubes. Such a lamp can be decorated with any lamp:

• chandelier;
• desk lamp;
• floor lamp;
• wall bra.

Lampshade from the tubes

Such lampshade will give soft and muted light, which will become a real highlight of any interior performed in any style. Here, as it is easy to guess, the main and only elements of the whole design will be paper tubes. They can be coated from both newspapers and colored paper. The main thing is remember, the appearance of the lampshar must complement the interior in the room.
The number of tubes depends on the size of the lamp to which it will be put on. "Pipe minimum", which should be turned, is 100 pieces. Between the tubes are attached with the help of the same PVA glue, thus forming the necessary form:

• circular;
• oval;
• square;
• arbitrary.

First, the first row is laid out, and then the whole design is increasing.

Note! The walls here need to be built in such a way that the lampshade expands to the center. For this, the diameter of the form should be gradually increased, and after the middle - gradually reduce.

If desired, the resulting lampshade, after it dries, you can paint the paint from the canister. The result is a solid product without flaws.
This is not a complete list of possible options for the manufacture of paper lamp. But these are the most popular ways that are implemented easily and quickly.

Conclusion

As you can see, make a paper lamp sufficiently enough. Here do not need expensive materials or a lot of time. With the exact following instructions, you can quickly cope with the task, and in your house there will have a new, beautiful and, without unnecessary modesty, the original lighting device.

Original lamps and lampshades do it yourself. Ideas, master classes

Lamps and lampshades do it yourself. Ideas, master classes

Hello everyone!

Creating or decoking lamps and lampshells The occupation is not only incredibly interesting, but also enough useful: it allows not only to create a unique subject, and in full compliance with the interior of your home, but also to save. It is enough to purchase the easiest lamp for little money and beat it to your taste. And there are options that and how to make a huge set, in a variety of techniques, using a wide variety of materials.

I picked up for us with you the idea of \u200b\u200bcreating and decorating lamps, I hope you can choose the appropriate option for yourself :) Pleasant viewing!

A lampshade decorated using decoupage technique, the base of the lamp is made of books

Decor of the metal frame of lampshar with feathers - very stylish :)

It is often enough to decorate the lampshades, fabric or paper flowers are used, the result is very romantic :)

Fabric flowers with candle processed

Cutting convolutions are used as colors

Flowers from twisted fabric

Ready Flowers used here

The flower is made of a stem strip of fabric, striking on one side and assembled in a bud

Spiral roses from newspapers

The bottom of the lamp is decorated with spiral paper roses

Decor of Ikeaevsky lampsome paper flowers

Lace and knitted napkins look very beautiful

The form attached with glue

The ball is inflated and the lace napkins are applied with the help of adhesive. After drying, the ball skeins, blown away and removed.

Very beautiful option: As the base of the lamp, the bird cage is used, the lamp shade is decorated in the decoupage technique with an outdated.

Even an umbrella can be used for chandelier :)

Even Loskutka trimming fabrics will go into business: wrapped, knotted. This option will be remarkably fit into the design of the country house or children's room.

Buttons-buttons

For the manufacture of lamps, various glass containers are used very often and successfully use banks, bottles. Just below, I led the master class on the manufacture of such a lamp.

A bottle as the base of the lamp - the bottom is also given a similar master class.

It is a bit more complicated here - the hole is drilled down on the back side of the bottle, through which the cord is started.

The lamp is made of figured metal sheet

Origami technology is successfully used to create lamps.

On the base of lampshar glued fabric strips

Lampshade from various retro leaves

Abazhur from the basket - why not? :)

The second life of metallic coland

Unnecessary fork-spoons created a very interesting version of the chandelier :)

Very cute solution: a metal mesh and beat the poultry is stretched on the frame. I think for the children's room.

And now bird subjects :)

Abjeur painting acrylic paints

Shallow veneer lamp

The base of the lamp is placed by marine shells

Knitted lampshades - look very comfortable :)

Decor of amusing memorable photos and slides

Flowers on this lamp - this is the bottom of plastic bottles :)

Lampshades are planted with paper circles

Vegetable lampshade :) I think, still a flower is frying there :)

Shashore from Shornov

Decoupage technique also applied here

Very interesting solution - wire as an art object :)

Lampshade decorated with cloth strips

Branch lamp

A lampshade is decorated with crumpled compressed coffee filters (forms for cupcakes)

Glass vase lamp

Base of lampshar - unnecessary toy soldiers, short and painted aerosol paint

Creative lap fetra

Shade from balls for ping pong :)

Flower decor

And many more, many different ideas ...

Master class on the manufacture of lamp from can & broit caps from Tom & Brit (BestOfinteriors.com)

We break through the nail hole to create a hole

Insert the patron

Stain in one color

Screw the light bulb and insert into the jar

Lamp is ready :)

Paper Lights from Varrell.com Resource

We will need an image of the castle

Cut out, cutting the winds, glue

Inside place a point lamp on batteries

Chandelier from a rope from Sarah M. Dorsey (sarahmdorseydesigns.blogspot.com)

We will need a rope, MOD Podge glue (can be replaced by diluted PVA), ball

In order to create a wavy shape, Sarah used wooden slats. We lay out the shape, we laughing glue for fixation.

After drying, we lay out on the ball and scrolling abundantly glue

After drying, remove the lampshade from the ball and stain in the white aerosol paint - the Sarah has four layers

Very beautiful lampshade of grandma squares from the author of the resource aboutgoodness.com

We are tightening with lampshane cloth

Strip tissue bend in half along and twist in roll

Run slightly

We apply glue on the fold and glue to the base

Master class to create a base for lampshar from Kiri (ilikethatlamp.com)

Necessary components

Bottle carefully mine, disinfect and dry

Covered aerosol paint

Mounting process

,

That's so a bottle of Jein has turned into a base for lampshar :)

As you can see, a sufficient thing is simple and very interesting. Give the will of your fantasy, create and let your home be beautiful and cozy!

Well, for those who still prefer to buy ready-made lighting devices, I recommend to look into a specialized Internet-shop Lampa.ua. - where in a huge assortment are high-quality and stylish desktop lights, chandeliers, sconces, accessories, etc. From the best manufacturers and at very flexible pleasant prices :) By the way, this online store according to Google statistics is the most popular among Ukrainian buyers :) Use with pleasure!

I wish everyone good luck and excellent mood !!

To create a lighting device, almost everything can be found at hand: wooden sticks, pieces of plinth, tanks, wood, metal wands and pipes, glass products, fabrics. Homemade lamps make futuristic, classic, glamorous, minimalist. For each type, several step-by-step master classes are invented. Designer premises are made to decorate unusual lamps. It can be products with slots, a variety of individual fragments, in the form of a large ball or cube. The same lamps are made with their own hands, from any material. They are engaged in this not only the masters selling their products, but also the usual owners of apartments and houses. Homemade chandeliers can be similar to the store or be carried out in an unusual way: from terkons, canned cans, etc. The form depends on the characteristics of the material and fantasy of the performer.

What can be used as materials

Read:

• fat cream;
• pVA glue;
• cotton buckle;
• dye;
• balloon.

There are some interesting options. From ordinary threads it turns out a beautiful glowing ball. First you need to inflate the ball and smear it with a cream. It is placed in a container with water and diluted in it. Then he is wounded by threads. The design is left to dry within 24 hours - it will only be left to put the product on the ceiling. The second way is to use the tubes. Sheets twist diagonally, sticking the tips are glued. You will need two hundred tubes: they glued together in a round or triangular figure. The following option is lamp shade: it is twisted into a spiral or conical shape. You can create a lamp from plastic bottles: they are cut off the bottom and neck. You will need a wire, acrylic paints, sealant and marker. There are many other techniques for creating a lamp with your own hands.

Options for creating lamps from wood

Making a lamp with your own hands is primarily art, not saving. Despite the fact that the tree is a simple and inexpensive material, products from it can compete with the rest of the quality of execution and aesthetics. The process of their manufacture will not be easier. It will be necessary to carry out complex calculations, work with a large number of tools, remove a lot of garbage. Lighting devices are made of sleep, branches, veneers, wooden rails, wooden boxes and frames, wheels, lanes, bars, etc. The lamp of the tree is the perfect solution for the interior, trimmed under the ancient. It can be made it from a piece of trunk or from treated materials, for example, in the form of a complex geometric design of sticks, rings, cylinders or a square created from four or eight bars.

Master class: how to make a lamp of a tree sleep

We will need a trunk of a tree, grinding machine, hacksaw, LED tape (2 m), brushes, wood varnish, glue, matte plastic tube. First, the barrel is cut into sections of the same thickness - about 2 cm. Then in the center of one of the sleeps is made template. He and all other sections are burned by markup. Measurements should be carried out carefully, due to poorly marked fragments, the whole process will have to begin again. After that, they must be pasted. The next step is to strengthen with glue and laying on gaskets for drying. After that, the logs are covered with varnish. In parallel, you can prepare a matte tube - a rod for construction. Its surface is processed to the maximum effect of mattness. The spears are put on the tube and then will still take one more step. The latter is mounted tape. It must be folded in his hands and in this form to put in the tube.

The list of necessary materials and tools includes: self-tapping screws, drill, chipboard, brush, acrylic varnish, electric shoe, 4 cartridges and 7 two-meter rails. From the chipboard you need to cut blanks, and their edges can be saved by the edge. Rakes are collected into a single design in the form of a cross-shaped diamond form in the center. The base is cut out of the 5-millimeter sheet of plywood. In places where the rails create intersections, pieces of bamboo sticks or seasons are installed. At the heart, it is necessary to drill 8 holes: 4 is intended for the ceiling, and as much for the main part of the lamp. From tin, you need to bend 4 corners with beveled edges. They are mounted in self-drawing so that open parts of the corners are directed inside the lampshar. The entire wooden frame is covered with varnish twice, with a drying break. At the end, the cross-shaped design is screwed by the confirmates.

It can be made of twelve stripes. For the inside, it takes a smaller - 60 cm, for external - 70 cm. Strips are made from the sheet: they are cut along the fibers with a steel line and a knife. On a large paper sheet, you must draw a circle with a diameter of 350 mm. It is divided into sectors of 30 °. On the left and right side of the lines separating the sectors, parallel lines are drawn along the perimeter of the circle to determine the desired position of the veneer strips. Then the disk with a small hole is prepared to lay the stripes. They are glued clockwise in the form of snowflakes, first three short, then three long. After drying the glue in the structures of the strips, it will take a hole with a width of about 1 cm. The wire is encountered through it, and the sleeve is attached to the disk. The hanging ends of the strips are fixed with the flange and bolts.

Lamps from textiles and threads

To create a lamp, you can use old clothes: jeans, golf, spoiled dresses, etc. The products are decorated with bows, pockets, threads with beads. In almost all cases, the fabric needs to wear on some framework. It can also be made with his own hands. It is better to choose a metal as a material, sometimes a tree. The basis for homemade chandelier from the fabric can be factory lamps, both new and old. The tissue of an ordinary old lamp lamp can be removed, and instead, consolidate modern, with stylish patterns. To create and design home-made chandeliers use threads of different thickness. They wind up various jars and frames, join the parts of the lamp and hang the design. Instructs look like lampshades of hardened threads. In addition, they also use twine or ropes. They successfully combine with different tissues and paper.

Master Class: Flood Flood Light

To create this product, you will need:

1. The base from the desktop lamp.
2. Glue.
3. Thick threads (up to 4 clubs).
4. Air balloons.

First inflated balls. Better somewhat, because they can burst. Their form should be perfect round. On each of them, the felt-tip pen is drawn a decade-cated circle. Through a hole of this size will be inserted with a light tube. The ball is placed on the loaf. Glue solution is prepared. In the hands you need to wear rubber gloves to glow threads into it. When they are impregnated with a solution, they get them; Then removed glue bunches. The end of the thread is tied to the node of the inflatable ball. After that, she is wrapped around the entire ball, it needs to be done evenly over the entire surface, but chaotic. It is advisable to use several threads of different colors. Then the ball is suspended until the design is dry. Then it is shoved, and the knot is cut off. The ball is extracted through a large hole, into which then you will need to insert a cartridge with a light bulb.

Label from fabric do it yourself

You will need dense paper, glue, cloth, threads under the color of the fabric, pins, line, pencil, iron. It will be necessary to make a template to calculate the desired amount of tissue. If the lamp shape must have a cylindrical shape, then the circle and height measure the corresponding lines alternately, creating a straight angle. The opposite sides of the rectangle are drawn. From the paper cuts the desired form. It is applied to the fabric. It requires a larger rectangle from it. It is cut after the desired fragment is selected. Then the matter is fixed on the template with a pin (its edges need to bend). After that you need to use a sewing machine. Processed fabric strokes iron. After that, it is glued to the base. Unprocessed sections are hiding. The seam is done so that the base is closed with a stitched edge.

Plastic chandeliers and lamps

Plastic became one of the most sought-after materials in the modern interior. This also applies to lamps - most diverse models are sold. You can make a chandelier with your own hands, which will not give up with finished products. The lighting device plander is constructed from anything. It can be disposable cups, various wands, painted plastic bottles. They are sometimes decorated with decorative devices: figures, luminous details. Various metal frames can be used as auxiliary material. The easiest way to make a desk lamp. You can use cut parts and shapes with holes. Instead of throwing out unnecessary plastic objects (used disposable dishes, etc.), it is better to try to make a small lamp that can decorate the room.

Master Class: We make plastic spoons

It is necessary to find a large number of identical plastic spoons, up to 200 pieces. Describe the product from integers will be more difficult, but if you cut them, then everything will turn out quickly and simple. Pens spoons need to cut off and remove, leaving only the breadwinner. Then you can use the finished lampshade for pasting the elements or cut it out of the eggplant. It makes the bottom of it and do a hole for a light bulb or the top of the neck is cut off, leaving a wide hole. Next you need to decide on the pattern. The upper surfaces of the cups will create a sink pattern, and the bottom - "schellow" surface. If you choose a second option, then jumpers should be glued to the core. First, it is separated by the upper part, laying out one by one rows of spoons. When the process comes to an open part, then you need to calculate everything so that the last row hid the cut edge of the core.

You can apply as fastening:

• glue;
• office plasticine;
• scotch.

Steel wire for frame, thin wire, soldering iron, scissors, ten plastic bottles of various shades of green. From the bottles you need to cut leaves of different sizes and shapes. Perfect fragments in the form of birch leaves and other leaves with a more or less compact form. Thus, it will be more elements. Sections, imitating plates, better handle the soldering iron to make them slightly bent. The edge of the sting should also be made by the veins: the leaves will gain a more natural look. Since the bottles have a cylindrical shape, the blanks will be with curvature. A hot needle is pierced holes for thin wires. You need at least two on each leaf, but even better four to turn the "eight" wire. Everything is worn as many sheets as possible. Then flexible wires are reliably twisted for the frame of steel wire.

You need to handle the soldering iron as much as possible so as not to burn your fingers and do not burn the leaves.

You can make several types of such lamps. Materials that will need: rubber legs, silicone sticks, a fluorescent lamp, a circle of fiberboard, CDs. Tools such as a triangle line, pencil, cigl, adhesive gun, screwdriver, pliers, ticks, drill. In the round form from the fiberboard there is a hole in the very center, it draws twelve sectors on it. On the lines that share them, one small opening is drilled. Steel wires will be stretched through them, each of which will be a stack of disks. The design will be quite heavy, so metal wires are needed. In a hole in a circle, a wire with a carton is shoved, a light bulb is inserted into it. From the disks you can also make a lamp-polyhedron, a globe in the form of a bowl, petals, a lamp ring.

Methods for creating paper lamps

This material is popular because of its flexibility. You can construct an interesting feature or folded the sheets of paper several times and make flowers. Folded paper sheets are combined into rounded shapes. Paper lamps are performed as plants, animals, abstraction. Some love to make patterns and cutouts. In individual countries of the East, chandeliers of rice paper are widely used. For the manufacture of the lamp, you can apply Origami technique. Paper luminaires are created by two main ways, namely using one or more large sheets or gluing a large number of paper elements. Over the past ten years, the popularity has acquired desktop and floor lamps. From paper you can make lamps, rugged pumpkins and houses. This material is suitable for creating a lampshade of traditional form:

• conical;
• cylindrical;
• elliptical.

From rice or parchment paper

Rice paper is useful for creating a Chinese lantern. Additionally, the thread, awl, the stationery knife, a ruler and a pencil. First on paper you need to mark. The lantern scheme consists of a variety of rhomb-shaped sectors. Half of them are filled with vertical intermittent markup. After that, the sheet is folded into the harmonic. It turns into a circle. To the top and to the bottom you can glue the painted covers. To make a plate of parchment paper, you will need a marking board, a circular knife, two leaf of parchment paper, two rolls of wax paper (similar to parchment), scissors, silk tape, suspended frame. The strips of a satin tape with a length of 18-20 cm and 40 cm are attached to the frame structure. The final stage lies in pasting on ribbons of mugs from parchment and waxed paper. Attach them you need a mustache.

Origami Chandelier from Paper Packages

To make such a lamp with your own hands, you will need a wire with a switch, a LED lamp, two paper packs with a pattern. First you need to learn how to do simple origami. The next case has the bottom of the packages, the handles are cleaned. They glue into one big paper bag. It is folded in half. Both parts are "turning" in the harmonica. You need 16 identical stripes. The extreme of them are diagonally. Sille pierced holes. One of the two open sides is reliably fixed by thick thread. It is necessary to leave the ability to regulate. The second will be open. The LED light bulb connects to the cartridge, the top of the lamp is open and closes back. It is necessary exactly such lighting, it is impossible to use incandescent lamps. The wire is fixed on the high decorative tree branch - the product is ready.

Products from corrugations look very original, so the material has become so popular. LED lamp, cable, thread, glue, knitting, spin, ruler, corrugated paper 44 × 88 cm fragment. First, it is necessary to take a ruler and handle and place paper on the line with the same width. Focusing on drawn lines, you need to make an even leaf accordion. With the help of the knitting needles, it is diagonally from one end, then returns to its original position and folds on the other side. Paper must be deployed again - diamonds should be released on it. The entire sheet now consists of double forms. The first and subsequent bend must be made by the corresponding bandwidth, otherwise the appearance of the paper will deteriorate. The billet twists in a spherical shape, and its upper part is fastened with the thread.

Butterfly chandelier

There are two ways to create such a lamp:

1. One big butterfly.
2. "Roy" of small moths of different sizes.

Babies of preschool age will like the lamp shade in the form of a variety of suspended figures. Separate parts of the lamp can descend to one and a half meters from the ceiling. The base is taken as the old lamp shade or its frame. If there are no such blanks, you can use rim from metal or wood or thick wire twisted in the circle. You need to prepare sheets with butterflies templates to select the butterflies of the necessary sizes and shapes. It is recommended to make moths at least five different sizes. Then the design will be visually greater. Butterflies are cut with small scissors or stationery knife. It is desirable that the paper is dense. Cut figures are painted with different colors, decorated with sparkles, but on some butterfly patterns can already be color. To bring the product to readiness, butterflies are fixed on the woods and fastened to the base.

The finished Chinese lamp can be used as a basis for other products. They are cheap. It will take an ideal round model. First option: Cut from the fabric circles of different colors and glue the mustache. From the Chinese ball you can do something like a round lamellar cone. The second method: circles cut out of the sheet paper sheets. They are connected in the center, the edges are lifted until the perfect flower turns out. Elements are attached to the ball ordered rows. Beautiful tartlets are obtained from paper sheets. They should be filled with something. Paper is also folded into square envelopes that can be turned into four conical molds. Some use the old wall card instead of paper. In any interior there will be a stylish newspaper lamp shade with printing images of gray or brown.

Metal pipe lamps and loft style tubes

Injunctioning water pipes with cranes can be mounted in a single design, equipped with light bulbs and create, so stylish and useful thing. It is better to post on the wall. This is a very popular element in Loft style. Luminaires are created from large and small pipes in steampunk style. These are complex designs, without special preparation to make them fail. However, you can construct a small robot with "head" in the form of a light bulb. Beautiful ceiling chandeliers are made from pipes. In addition, there are a variety of models of lamps made of metal pipes. Brass is often used as material. Chandeliers are created in the form of compositions of several tubes. Pipes, as a rule, are made suitable, but lamps with various patterns and openings are also produced. They are not inferior in popularity lamps in the Loft style.

You can make it possible to make a beautiful product in the form of a brilliant facet. In addition to the pipes themselves, sandpaper, jigsaw, twine or wire, gloves will be required. To create an original chandelier, you will need 20 pipes: 10 short (6 cm), 5 medium (12 cm) and as many long (25 cm). It is necessary to find a few long blanks, place them and cut the jigsaw. After that, you need to grind the sanding paper, so that the edges of the tubes are perfectly smooth. Further fragments are collected on thick wire or the twine. First, horizontal rows are created: the lower out of five short and medium from the same number of medium tubes. Then they are connected by five more short tubes. The upper part of the design is made of five long fragments that need to be combined with the already cooked part. Long pipes are not completely reduced, in this place you need to fix the cartridge.

Lamps from sanitary pipes

It is necessary to prepare such devices as an electrical cable, tape, tape, different screwdrivers, two-tier wire, cartridges, hinges, fittings that match the parameters of pipes. One of the tubes should be more - it is she who serves to fasten the ceiling. The assembly process is quite complex. It is necessary to create a scheme on paper, and already be accepted for business. At this stage are determined with the configuration of the structure. Splitters need to be combined correctly. All parts of the prepared design can be polished and painted. Preference is better to give white, red, gold and black colors. You need to wait about a day so that everything is completely dried. After that, all pipes are collected together. They are tightened with light bulbs. The last stage is a connection. Since the scheme is complicated, it is better to invite a specialist.

Using glass to create lamps

On the ceiling you can hang a composition of several empty bottles of alcoholic beverages. Three-liter banks can be swallowed for metal chains. Glass dishes are also suitable as a ceiling. The lamp made of multiple glass fragments can mimic a crystal chandelier. Broken glass objects find a new purpose in the form of an original lighting device. Beautiful desktop lamps are created from glasses and fuels. Various glass boxes can be useful, glass from old wall bras, headlights, interior doors. A homemade glass chandelier can be calculated by watercolor or stained in paints. It turns out beautiful stained glass windows. To create suspended lamps, the masters use a variety of decorative containers from under oils and perfumes. Unlike wood and paper, glass has high fire safety.

The list of necessary fixtures includes nippers, screwdrivers, screws, glass cutter, silicone, rag, or brush, stool, pine boards, hooks, chain, ten light bulbs, wiring, bottles from wine. The first thing is handled the containers. Labels and remnants of glue are removed from the bottles. With the help of glass cutters you need to remove the bottom of each bottle: it rests on an altitude of 1-2 cm, and the bottle is spinning around its axis. Cracks need to be sufficient with a hammer until the bottom does not disappear. After that, the electric pipes are placed in bottles and connected with cartridges. They screw light bulbs. Now you need to cook boards. In the lower, greater, hole holes for torn and wires are burned. The top will collect them in one bundle. The hooks for chains that will hold the design are screwed into the lower board. For the kitchen you can make a desktop lamp with a base of a bottle and a plastic from a tree.

Wooden boards can be covered with mourn to give the effect of "old".

Use old cans to create lamps

Old jars can find a new destination. Luminaires can be created using threads, electrical wires, cans for cans. Capacities need to be equipped with handles. They will need to be tied with threads that are fastened to the prepared pre-iron frame. Electrades with cartridges and light bulbs are lowered in banks - the chandelier is ready. You can make an option for giving - Threads are tied around the branches of the tree, and candles or small lanterns are put inside the cans. Beautifully look at the containers, wrapped with multi-colored threads or decorated with patterned napkins. The inner of the cans can be painted in white, and while it has not yet dried, apply a drawing in the form of chaotic lines. Some paint the container from the outer side with different colors, and on top paint an image using wicked shadows. Banks can also be saved with small glass.

Chandelier / Shebbi-Chic Lamp

Beautiful decorative things are created from beads and fabrics, including lamps characteristic of this stylist. SHEBBI-SHIC decoration provides that the room is designed for a girl or a woman. You will need beads, beads, threads, chains, cartridge with a lamp, ready wooden or metal frame. First of all, you need to paint the foundation in some of the soft shades. After that, it can be wrapped in decorative elements or cloth. The top of the ceiling is winding smaller beads, but in more - one thread should be rolled to 40 beads, and about 20 on the lower threads - about 20. This is an exemplary proportion, it, like the tension of the threads, can be changed depending on the size of the design. The lamp is usually tightened with a pink cloth. All decorations suspend so that they flow down.

Conclusion

The chandelier is the only important element of the top of the room, it can create symmetry and other geometric accents. To hang in your room beautiful, stylish, designer lamp, not necessarily buy it in the store. Each house has enough items and tools to do everything on their own. In most cases, there is enough workpiece, scissors, paper, glue, thread, frame, varnish and paints. Sometimes it may be necessary to help the electrician specialist. Most of the "handmade" lamps are performed from wood, plastic, paper, glass, textiles or metals. More exotic options are found using different designs, small parts, molds. A homemade chandelier should not only perform aesthetic function, but also high quality room. Design it follows with the mind.

Paper lamp is possible? And original and beautiful? Oddly enough, yes. And you can make sure of this by reading our article. Of course, not the lamp itself, but its lampshade. Naturally, due to the briefness and fragility of the material, such a lamp is not cleaned or washing, and simply with time is disposed of. But before that moment, he will be enough to please you with its stylish outlines, and the consciousness that you created this beauty with your own hands. How to make such a stylish and unusual paper lamp lamp, we will tell in detail in our article.

Making a paper lamp

For the manufacture of lampshar, we will need:

• Nine sheets sufficiently dense white paper A4 format
• Two sheets of white slim cardboard A4 format
• Rule
• Pencil
• Paper knife
• Thin stationery scotch
• Glue stick
• Super glue
• Eraser
• Compass

With the help of a ruler and pencil on a sheet of paper with a wide face pointing the middle. A similar label and from the opposite side.

In the same way, we celebrate the middle and on the side parts of the sheet, on both sides.

We connect the dots of the line with the help of a pencil and a ruler, as shown in the photo above.

Then spend the lines from the point to the point, on one side to the other opposite.

On the central, horizontal line, retreating from the edge of the sheet, lay three sections of 2.4 centimeters long.

Then, from the marked segments, we carry out vertical lines perpendicular to the central line.

Then similar actions do from the opposite side by turning the sheet "upside down".

With the help of a paper knife, cut out the workpiece, erased by an extraction lines conducted by a pencil.

Here is such a primary workpiece with us. For lampshar, they need nine pieces.

We fold the workpiece, selling the deepest slots in each other.

In the same way, other blanks are collapsed.

We connect two blanks with each other, combining, promoting each other, medium slots.

Small, extreme slots with further connection serve to finalize fragments.

It turns out such a complicated segment.

Thus, we combine all nine blanks, then, turning the future lampshade with an arched tube of sides inside, tighten two finite fragments described above in the method - medium slots.

Ends of paper fragments fix, aligning small slots.

Further, with the help of a circulation, on a sheet of cardboard, the shafts of the blanks of the fastening base as in the photo above, and cut them with a paper knife. Cut from two sheets, covering them among themselves with scotch, so as not to bother with re-drawing of similar fragments.

We have four paper rings, and four paper circles with a hole in the center (for electric shuffle) and a slot.

We glue the same fragments together with a pencil glue to get a solid fastening basis.

We insert a paper ring into the billet of the lamp by the lamp and fix with the superclone. This ring allows the lamp to keep the shape and prevents the deformation.

Wake up a cord with a light bulb into a paper circle slot. I turn over the lampshade so that the paper ring glued earlier turned out to be below.

Insert into lampshane

Insert the paper circle into the lampshade, as shown in the photo.

We glue with a superclone. Abazhur ready. You can use.

Important!!!

Attention! Paper lampshades are unsafe in terms of fire safety. Therefore, in order to avoid fire, in the manufacture of such lamps should not be used by incandescent lamps. It is better to use a LED or energy-saving light bulb.

How to make a paper lamp / video /

Unusual paper lamp

Paper lantern

Lumina lamp

Table lamp do it yourself

Output:

A beautiful lamp, made personally, .. It would seem normal paper, and how many ideas can be embodied .. See the videos to our article to see all the variety of ways, create, and enjoy the result.